Support of new Cisco Catalyst 9800 Series Wireless Controller

[sysoff]

"New Syntax Highlighting"

Which Syntax?

IOS-XE

Link to Command Reference

https://www.cisco.com/c/en/us/td/docs/wireless/controller/9800/17-3/cmd-ref/b_wl_17_3_cr.html

[heyglen]

The link you pasted contains ~600 commands.

If you provide a sample with some typical configuration, I can prioritize implementing those commands instead.

[sysoff]

Hi heyglen. This should be the most important/typical set of commands with some variations. If you can add all the options within this ones for now it would be nice: wlan <Profile_Name> 1 <SSID_NAME> no bss-transition channel-scan defer-priority 0 channel-scan defer-priority 1 channel-scan defer-priority 2 channel-scan defer-priority 3 channel-scan defer-priority 4 channel-scan defer-priority 7 channel-scan defer-time 500 radio dot11a no security ft adaptive security dot1x authentication-list <RADIUS_Auth_List> no shutdown ! wlan <Profile_Name> 2 <SSID_NAME> no bss-transition channel-scan defer-priority 0 channel-scan defer-priority 1 channel-scan defer-priority 2 channel-scan defer-priority 3 channel-scan defer-priority 4 channel-scan defer-priority 7 channel-scan defer-time 500 mac-filtering default radio dot11bg no security ft adaptive peer-blocking drop security wpa psk set-key ascii 0 <PSK> no security wpa akm dot1x security wpa akm psk no shutdown ! wireless tag policy <NAME> description <Description> wlan <WLAN1> policy <Policy1> wlan <WLAN2> policy <Policyx> wlan <WLAN3> policy <Policyx> ! wireless profile policy <NAME> accounting-list <NAME> description <Descripiton> dhcp-tlv-caching http-tlv-caching ipv4 dhcp required ipv4 flow monitor wireless-avc-basic input ipv4 flow monitor wireless-avc-basic output mdns-sd service-policy aireos-default-mdns-profile session-timeout 86400 subscriber-policy-name <NAME> vlan <interface_or_vlan-id> no shutdown ! wireless profile flex <NAME> no arp-caching description <Description> native-vlan-id <vlan-id> vlan-name VLAN4 vlan-id 4 vlan-name VLAN2 vlan-id 2 ! wireless tag site <NAME> ap-profile <NAME> description <Description> flex-profile <NAME> no local-site ! ap profile <NAME> capwap backup primary <NAME> <IP_ADDRESS> capwap backup secondary <NAME> <IP_ADDRESS> description <Description> hyperlocation ble-beacon 0 hyperlocation ble-beacon 1 hyperlocation ble-beacon 2 hyperlocation ble-beacon 3 hyperlocation ble-beacon 4 ntp ip <IP_ADDRESS> preferred-mode ipv4 ! ap ffff.ffff.ffff policy-tag <NAME> site-tag <NAME> !

…

________________________________ From: Glen Harmon <notifications@github.com> Sent: Friday, August 28, 2020 8:07 AM To: heyglen/network_tech <network_tech@noreply.github.com> Cc: sysoff <pjfh4@hotmail.com>; Author <author@noreply.github.com> Subject: Re: [heyglen/network_tech] Support of new Cisco Catalyst 9800 Series Wireless Controller (#36) The link you pasted contains ~600 commands. If you provide a sample with some typical configuration, I can prioritize implementing those commands instead. — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub<#36 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AONUVNDNEQUPQVDUYJ3CBVDSC5JSXANCNFSM4QMK7Y2Q>.

[heyglen]

I don't have a syntax definition for IOS-XE. Before I can start building this I need to implement some basics: config t, interface eth1, etc.

Implementing this is a long way off... sorry :(

[sysoff]

I don't have a syntax definition for IOS-XE. Before I can start building this I need to implement some basics: config t, interface eth1, etc.

Implementing this is a long way off... sorry :(

Hi heyglen,

IOS-XE is very similar to IOS.
Is in place for some time now in Cisco routers and switch's, etc. If it helps, I can share with you a IOS-XE configuration.
I'm using IOS syntax to create and analyse IOS-XE configurations.

Best Regards,