Led_strip interferes with voltage and current reporting #3853
Description
Current Behavior
It seems that whenever I turn on led_strip my board doesn't not report battery voltage and current. Everything is configured correctly and the Leds are working fine. When I disable led_strip vbat and current are reported as normal on inav configurator and s.port telemetry.
CLI:
diff
version
INAV/KAKUTEF4V2 2.0.0 Aug 19 2018 / 21:14:39 (dbdd165)
resources
mixer
mmix 0 1.000 -1.000 1.000 -1.000
mmix 1 1.000 -1.000 -1.000 1.000
mmix 2 1.000 1.000 1.000 1.000
mmix 3 1.000 1.000 -1.000 -1.000
servo mix
servo
feature
feature -TX_PROF_SEL
feature THR_VBAT_COMP
feature VBAT
feature GPS
feature CURRENT_METER
feature LED_STRIP
feature BLACKBOX
feature AIRMODE
feature PWM_OUTPUT_ENABLE
beeper
map
serial
serial 0 32 115200 38400 0 115200
serial 3 2 115200 115200 0 115200
led
led 0 6,11::CB:1
led 1 7,11::CB:1
led 2 8,11::CB:1
led 3 8,12::CB:1
led 4 7,12::CB:1
led 5 6,12::CB:1
led 6 6,13::CB:1
led 7 7,13::CB:1
led 8 8,13::CB:1
led 9 8,14::CB:1
led 10 7,14::CB:1
led 11 6,14::CB:1
led 12 1,11::CN:2
led 13 2,11::CN:2
led 14 2,12::CN:2
led 15 1,12::CN:2
led 16 1,13::CN:2
led 17 2,13::CN:2
led 18 11,11::CN:2
led 19 12,11::CN:2
led 20 12,12::CN:2
led 21 11,12::CN:2
led 22 11,13::CN:2
led 23 12,13::CN:2
color
mode_color
aux
aux 0 0 0 1750 2100
aux 1 1 1 1300 2100
aux 2 4 1 1700 2100
aux 3 9 1 1700 2100
aux 4 8 2 1875 2100
aux 5 21 2 1425 1575
aux 6 12 2 900 1175
adjrange
rxrange
osd_layout
osd_layout 0 0 13 1 V
osd_layout 0 1 1 12 V
osd_layout 0 4 8 6 H
osd_layout 0 7 17 11 V
osd_layout 0 9 1 2 H
osd_layout 0 11 24 12 V
osd_layout 0 12 17 12 V
osd_layout 0 13 4 6 V
osd_layout 0 14 21 2 V
osd_layout 0 15 21 6 V
osd_layout 0 22 17 3 V
osd_layout 0 23 10 3 V
osd_layout 0 28 21 1 V
osd_layout 0 30 1 8 V
osd_layout 0 31 21 3 H
osd_layout 0 32 2 8 H
osd_layout 0 34 10 10 V
osd_layout 0 38 2 10 V
osd_layout 0 40 2 2 V
osd_layout 0 46 2 2 H
osd_layout 0 48 8 12 V
osd_layout 0 49 23 7 H
osd_layout 0 53 1 11 V
osd_layout 1 45 0 0 V
master
set gyro_sync = ON
set gyro_hardware_lpf = 188HZ
set gyro_lpf_hz = 70
set gyro_notch1_hz = 170
set gyro_notch1_cutoff = 125
set gyro_notch2_hz = 85
set gyro_notch2_cutoff = 43
set acc_hardware = MPU6500
set acczero_x = 27
set acczero_y = -9
set acczero_z = -8
set accgain_x = 4092
set accgain_y = 4093
set accgain_z = 4018
set align_mag = CW270FLIP
set mag_hardware = HMC5883
set magzero_x = 81
set magzero_y = -35
set magzero_z = 37
set baro_hardware = BMP280
set pitot_hardware = NONE
set rssi_channel = 8
set blackbox_rate_denom = 5
set blackbox_device = SPIFLASH
set min_throttle = 1035
set motor_pwm_rate = 8000
set motor_pwm_protocol = MULTISHOT
set failsafe_procedure = RTH
set current_meter_scale = 290
set model_preview_type = 3
set switch_disarm_delay = 100
set gps_sbas_mode = EGNOS
set gps_ublox_use_galileo = ON
set nav_auto_speed = 600
set nav_manual_speed = 600
set nav_land_slowdown_minalt = 125
set nav_land_slowdown_maxalt = 550
set nav_min_rth_distance = 700
set nav_rth_altitude = 1500
set nav_mc_hover_thr = 1450
set smartport_uart_unidir = ON
set osd_rssi_alarm = 40
set osd_time_alarm = 8
set name = BEHEMOTH
profile
profile 1
set mc_p_pitch = 75
set mc_i_pitch = 50
set mc_d_pitch = 30
set mc_p_roll = 75
set mc_i_roll = 50
set mc_d_roll = 30
set mc_p_yaw = 95
set mc_p_level = 27
set max_angle_inclination_rll = 450
set max_angle_inclination_pit = 600
set dterm_notch_hz = 125
set dterm_notch_cutoff = 90
set rate_accel_limit_roll_pitch = 3600
set rate_accel_limit_yaw = 720
set heading_hold_rate_limit = 30
set roll_rate = 55
set pitch_rate = 55
set yaw_rate = 25
battery_profile
battery_profile 1
set bat_cells = 4
set battery_capacity = 1300
set battery_capacity_warning = 390
set battery_capacity_critical = 260
- FC Board name and vendor: Hollybro Kakute F4V2
- INAV version string: 2.0