[HCL] CyberPower CP1500EPFCLCD supported by usbhid-ups

[living180]

CyberPower CP1500EPFCLCD (European version of the CP1500PFCLCD): http://www.cyberpower-eu.com/products/ups_systems/pfc-sinewave/cp1500epfclcd.htm

Shutdown sequence tested successfully via USB using NUT 2.7.3.

upsc output:

battery.charge: 100
battery.charge.low: 10
battery.charge.warning: 20
battery.mfr.date: CPS
battery.runtime: 2640
battery.runtime.low: 300
battery.type: PbAcid
battery.voltage: 24.0
battery.voltage.nominal: 24
device.mfr: CP1500EPFCLCD
device.model: CRJB103.551
device.serial: CPS
device.type: ups
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.parameter.synchronous: no
driver.version: 2.7.3
driver.version.data: CyberPower HID 0.4
driver.version.internal: 0.39
input.transfer.high: 260
input.transfer.low: 170
input.voltage: 237.0
input.voltage.nominal: 230
output.voltage: 269.0
ups.beeper.status: disabled
ups.delay.shutdown: 20
ups.delay.start: 30
ups.load: 19
ups.mfr: CP1500EPFCLCD
ups.model: CRJB103.551
ups.productid: 0501
ups.realpower.nominal: 900
ups.serial: CPS
ups.status: OL
ups.test.result: No test initiated
ups.timer.shutdown: -60
ups.timer.start: -60
ups.vendorid: 0764

upsrw output:

[battery.charge.low]
Remaining battery level when UPS switches to LB (percent)
Type: STRING
Maximum length: 10
Value: 10

[battery.runtime.low]
Remaining battery runtime when UPS switches to LB (seconds)
Type: STRING
Maximum length: 10
Value: 300

[input.transfer.high]
High voltage transfer point (V)
Type: STRING
Maximum length: 10
Value: 260

[input.transfer.low]
Low voltage transfer point (V)
Type: STRING
Maximum length: 10
Value: 170

[ups.delay.shutdown]
Interval to wait after shutdown with delay command (seconds)
Type: STRING
Maximum length: 10
Value: 20

[ups.delay.start]
Interval to wait before (re)starting the load (seconds)
Type: STRING
Maximum length: 10
Value: 30

upscmd -l output:

Instant commands supported on UPS [cyberpower]:

beeper.disable - Disable the UPS beeper
beeper.enable - Enable the UPS beeper
beeper.mute - Temporarily mute the UPS beeper
beeper.off - Obsolete (use beeper.disable or beeper.mute)
beeper.on - Obsolete (use beeper.enable)
load.off - Turn off the load immediately
load.off.delay - Turn off the load with a delay (seconds)
load.on - Turn on the load immediately
load.on.delay - Turn on the load with a delay (seconds)
shutdown.return - Turn off the load and return when power is back
shutdown.stayoff - Turn off the load and remain off
shutdown.stop - Stop a shutdown in progress
test.battery.start.deep - Start a deep battery test
test.battery.start.quick - Start a quick battery test
test.battery.stop - Stop the battery test

[clepple]

Thanks for a very complete compatibility report!

Do all the measurements look reasonable to you? I'm not too familiar with the voltage readings one might expect on a non-120V system, but the difference between input.voltage and output.voltage seems large to me. Which is closer to the LCD reading?

[living180]

input.voltage is accurate - output.voltage is bogus. When on mains power the LCD shows the input voltage as being the same as the output voltage. It looks like the US version has a similar issue with output.voltage: http://networkupstools.org/ddl/Cyber_Power_Systems/CP1500PFCLCD.html. I just did a quick test running upsc with the UPS disconnected from mains power, and input.voltage was 0.0 while output.voltage was 262.0, which is still bogus.

[clepple]

@living180 one more quick question: does device.model correspond to the serial number on the label?

[living180]

No, I only found one label on the exterior case. It has no description - just a barcode with some characters underneath, but it is the only thing that resembles a serial number. It is different than device.model however, and there doesn't seem to be any relation between them.

[WillyTP]

Hello, as 15/01/2025 I report issue of wrong Output Voltage reading.
Updated UPS manufacturer page: https://www.cyberpower.com/eu/en/product/sku/cp1500epfclcd

upsc output:
battery.charge: 2
battery.charge.low: 10
battery.charge.warning: 20
battery.mfr.date: CPS
battery.runtime: 51
battery.runtime.low: 300
battery.type: PbAcid
battery.voltage: 24.0
battery.voltage.nominal: 24
device.mfr: CPS
device.model: CP1500EPFCLCD
device.serial: CRMMYxxx (checked, it's correct)
device.type: ups
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 5
driver.parameter.port: auto
driver.parameter.synchronous: no
driver.version: DSM7-2-1-69057-NM-nano-4-C1-240105
driver.version.data: CyberPower HID 0.4
driver.version.internal: 0.41
input.transfer.high: 260
input.transfer.low: 170
input.voltage: 232.0
input.voltage.nominal: 230
output.voltage: 264.0
ups.beeper.status: enabled
ups.delay.shutdown: 20
ups.delay.start: 30
ups.load: 15
ups.mfr: CPS
ups.model: CP1500EPFCLCD
ups.productid: 0501
ups.realpower.nominal: 900
ups.serial: CRMMY2000017
ups.status: OL CHRG LB
ups.test.result: Done and warning
ups.timer.shutdown: -60
ups.timer.start: -60
ups.vendorid: 0764

Kind regards