Update 5.4-2.1.x-imx to v5.4.83 #191
Merged
Conversation
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
…t-irq pin to output commit e2b7441 upstream Suspending Goodix touchscreens requires changing the interrupt pin to output before sending them a power-down command. Followed by wiggling the interrupt pin to wake the device up, after which it is put back in input mode. On Cherry Trail device the interrupt pin is listed as a GpioInt ACPI resource so we can do this without problems as long as we release the IRQ before changing the pin to output mode. On Bay Trail devices with a Goodix touchscreen direct-irq mode is used in combination with listing the pin as a normal GpioIo resource. This works fine, but this triggers the WARN in byt_gpio_set_direction-s output path because direct-irq support is enabled on the pin. This commit replaces the WARN call with a dev_info_once call, fixing a bunch of WARN splats in dmesg on each suspend/resume cycle. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
…..., GPIOD_OUT_HIGH) commit 156abe2 upstream The pins on the Bay Trail SoC have separate input-buffer and output-buffer enable bits and a read of the level bit of the value register will always return the value from the input-buffer. The BIOS of a device may configure a pin in output-only mode, only enabling the output buffer, and write 1 to the level bit to drive the pin high. This 1 written to the level bit will be stored inside the data-latch of the output buffer. But a subsequent read of the value register will return 0 for the level bit because the input-buffer is disabled. This causes a read-modify-write as done by byt_gpio_set_direction() to write 0 to the level bit, driving the pin low! Before this commit byt_gpio_direction_output() relied on pinctrl_gpio_direction_output() to set the direction, followed by a call to byt_gpio_set() to apply the selected value. This causes the pin to go low between the pinctrl_gpio_direction_output() and byt_gpio_set() calls. Change byt_gpio_direction_output() to directly make the register modifications itself instead. Replacing the 2 subsequent writes to the value register with a single write. Note that the pinctrl code does not keep track internally of the direction, so not going through pinctrl_gpio_direction_output() is not an issue. This issue was noticed on a Trekstor SurfTab Twin 10.1. When the panel is already on at boot (no external monitor connected), then the i915 driver does a gpiod_get(..., GPIOD_OUT_HIGH) for the panel-enable GPIO. The temporarily going low of that GPIO was causing the panel to reset itself after which it would not show an image until it was turned off and back on again (until a full modeset was done on it). This commit fixes this. This commit also updates the byt_gpio_direction_input() to use direct register accesses instead of going through pinctrl_gpio_direction_input(), to keep it consistent with byt_gpio_direction_output(). Note for backporting, this commit depends on: commit e2b7441 ("pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output") Cc: stable@vger.kernel.org Fixes: 86e3ef8 ("pinctrl: baytrail: Update gpio chip operations") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> [sudip: use byt_gpio and vg->pdev->dev for dev_info()] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drop the added selftest as it depends on functionality that doesn't exist in 5.4. Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a4b98a7 upstream. The function may be unbound causing the ffs_ep and its descriptors to be freed while userspace is in the middle of an ioctl requesting the same descriptors. Avoid dangling pointer reference by first making a local copy of desctiptors before releasing the spinlock. Fixes: c559a35 ("usb: gadget: f_fs: add ioctl returning ep descriptor") Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Vamsi Krishna Samavedam <vskrishn@codeaurora.org> Signed-off-by: Jack Pham <jackp@codeaurora.org> Cc: stable <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201130203453.28154-1-jackp@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46ee4ab upstream. Add PID for CH340 that's found on a ch341 based Programmer made by keeyees. The specific device that contains the serial converter is described here: http://www.keeyees.com/a/Products/ej/36.html The driver works flawlessly as soon as the new PID (0x5512) is added to it. Signed-off-by: Jan-Niklas Burfeind <kernel@aiyionpri.me> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf193bf upstream. Keep the device-id entries sorted to make it easier to add new ones in the right spot. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e4d659 upstream. Update the USB serial option driver support for the Fibocom NL668 Cat.4 LTE modules as there are actually several different variants. Got clarifications from Fibocom, there are distinct products: - VID:PID 1508:1001, NL668 for IOT (no MBIM interface) - VID:PID 2cb7:01a0, NL668-AM and NL652-EU are laptop M.2 cards (with MBIM interfaces for Windows/Linux/Chrome OS), respectively for Americas and Europe. usb-devices output for the laptop M.2 cards: T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(misc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=01a0 Rev=03.18 S: Manufacturer=Fibocom Wireless Inc. S: Product=Fibocom NL652-EU Modem S: SerialNumber=0123456789ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) I: If#= 4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none) Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d6556c upstream. There is a single option port in this modem, and it is used as debug port. lsusb -v for this device: Bus 001 Device 002: ID 1e2d:006c Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 239 Miscellaneous Device bDeviceSubClass 2 ? bDeviceProtocol 1 Interface Association bMaxPacketSize0 64 idVendor 0x1e2d idProduct 0x006c bcdDevice 0.00 iManufacturer 4 iProduct 3 iSerial 5 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 243 bNumInterfaces 7 bConfigurationValue 1 iConfiguration 2 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 1 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 2 CDC Union: bMasterInterface 1 bSlaveInterface 2 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 3 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 CDC Header: bcdCDC 1.10 CDC ACM: bmCapabilities 0x02 line coding and serial state CDC Call Management: bmCapabilities 0x03 call management use DataInterface bDataInterface 4 CDC Union: bMasterInterface 3 bSlaveInterface 4 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Association: bLength 8 bDescriptorType 11 bFirstInterface 5 bInterfaceCount 2 bFunctionClass 2 Communications bFunctionSubClass 2 Abstract (modem) bFunctionProtocol 1 AT-commands (v.25ter) iFunction 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 6 Ethernet Networking bInterfaceProtocol 0 iInterface 0 CDC Header: bcdCDC 1.10 CDC Ethernet: iMacAddress 1 (??) bmEthernetStatistics 0x00000000 wMaxSegmentSize 16384 wNumberMCFilters 0x0001 bNumberPowerFilters 0 CDC Union: bMasterInterface 5 bSlaveInterface 6 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 0 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 1 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Signed-off-by: Giacinto Cifelli <gciofono@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c98fff7 upstream. This is a partial revert of commit 2bb70f0 ("USB: serial: option: support dynamic Quectel USB compositions") The Quectel BG96 is different from most other modern Quectel modems, having serial functions with 3 endpoints using ff/ff/ff and ff/fe/ff class/subclass/protocol. Including it in the change to accommodate dynamic function mapping was incorrect. Revert to interface number matching for the BG96, assuming static layout of the RMNET function on interface 4. This restores support for the serial functions on interfaces 2 and 3. Full lsusb output for the BG96: Bus 002 Device 003: ID 2c7c:0296 Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x2c7c idProduct 0x0296 bcdDevice 0.00 iManufacturer 3 Qualcomm, Incorporated iProduct 2 Qualcomm CDMA Technologies MSM iSerial 4 d1098243 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 145 bNumInterfaces 5 bConfigurationValue 1 iConfiguration 1 Qualcomm Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 254 bInterfaceProtocol 255 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0000 (Bus Powered) Cc: Sebastian Sjoholm <sebastian.sjoholm@gmail.com> Fixes: 2bb70f0 ("USB: serial: option: support dynamic Quectel USB compositions") Signed-off-by: Bjørn Mork <bjorn@mork.no> Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 54ffccb upstream. tiocspgrp() takes two tty_struct pointers: One to the tty that userspace passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`). These pointers are different when ioctl() is called with a master fd. To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock. This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on both sides of a PTY pair to corrupt the refcount of `struct pid`, leading to use-after-free errors. Fixes: 47f8683 ("redo locking of tty->pgrp") CC: stable@kernel.org Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c8bcd9c upstream. Currently, locking of ->session is very inconsistent; most places protect it using the legacy tty mutex, but disassociate_ctty(), __do_SAK(), tiocspgrp() and tiocgsid() don't. Two of the writers hold the ctrl_lock (because they already need it for ->pgrp), but __proc_set_tty() doesn't do that yet. On a PREEMPT=y system, an unprivileged user can theoretically abuse this broken locking to read 4 bytes of freed memory via TIOCGSID if tiocgsid() is preempted long enough at the right point. (Other things might also go wrong, especially if root-only ioctls are involved; I'm not sure about that.) Change the locking on ->session such that: - tty_lock() is held by all writers: By making disassociate_ctty() hold it. This should be fine because the same lock can already be taken through the call to tty_vhangup_session(). The tricky part is that we need to shorten the area covered by siglock to be able to take tty_lock() without ugly retry logic; as far as I can tell, this should be fine, since nothing in the signal_struct is touched in the `if (tty)` branch. - ctrl_lock is held by all writers: By changing __proc_set_tty() to hold the lock a little longer. - All readers that aren't holding tty_lock() hold ctrl_lock: By adding locking to tiocgsid() and __do_SAK(), and expanding the area covered by ctrl_lock in tiocspgrp(). Cc: stable@kernel.org Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Jiri Slaby <jirislaby@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c84bfed upstream. ASUS Zephyrus G14 has two speaker pins, and the auto-parser tries to assign an individual DAC to each pin as much as possible. Unfortunately the third DAC has no volume control unlike the two DACs, and this resulted in the inconsistent speaker volumes. As a workaround, wire both speaker pins to the same DAC by modifying the existing quirk (ALC289_FIXUP_ASUS_GA401) applied to this device. Since this quirk entry is chained by another, we need to avoid applying the DAC assignment change for it. Luckily, there is another quirk entry (ALC289_FIXUP_ASUS_GA502) doing the very same thing, so we can chain to the GA502 quirk instead. Note that this patch uses a new flag of the generic parser, obey_preferred_dacs, for enforcing the DACs. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210359 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201127141104.11041-2-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aeedad2 upstream. HP Spectre x360 Convertible 15" version (SSID 103c:827f) needs the same quirk to make the mute LED working like other models. System Information Manufacturer: HP Product Name: HP Spectre x360 Convertible 15-bl1XX Sound Codec: Codec: Realtek ALC295 Vendor Id: 0x10ec0295 Subsystem Id: 0x103c827f Revision Id: 0x100002 Reported-by: <christoph.plattner@gmx.at> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201128090015.7743-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit eeacd80 upstream. Some laptops like ASUS UX482EG & B9400CEA's headset audio does not work until the quirk ALC294_FIXUP_ASUS_HPE is applied. Signed-off-by: Jian-Hong Pan <jhp@endlessos.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201124092024.179540-1-jhp@endlessos.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5782a5 upstream. Enable new codec supported for ALC897. Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/3b00520f304842aab8291eb8d9191bd8@realtek.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 242d990 upstream. The generic parser accepts the preferred_dacs[] pairs as a hint for assigning a DAC to each pin, but this hint doesn't work always effectively. Currently it's merely a secondary choice after the trial with the path index failed. This made sometimes it difficult to assign DACs without mimicking the connection list and/or the badness table. This patch adds a new flag, obey_preferred_dacs, that changes the behavior of the parser. As its name stands, the parser obeys the given preferred_dacs[] pairs by skipping the path index matching and giving a high penalty if no DAC is assigned by the pairs. This mode will help for assigning the fixed DACs forcibly from the codec driver. Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201127141104.11041-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4c75b0f upstream. On powerpc, kprobe-direct.tc triggered FTRACE_WARN_ON() in ftrace_get_addr_new() followed by the below message: Bad trampoline accounting at: 000000004222522f (wake_up_process+0xc/0x20) (f0000001) The set of steps leading to this involved: - modprobe ftrace-direct-too - enable_probe - modprobe ftrace-direct - rmmod ftrace-direct <-- trigger The problem turned out to be that we were not updating flags in the ftrace record properly. From the above message about the trampoline accounting being bad, it can be seen that the ftrace record still has FTRACE_FL_TRAMP set though ftrace-direct module is going away. This happens because we are checking if any ftrace_ops has the FTRACE_FL_TRAMP flag set _before_ updating the filter hash. The fix for this is to look for any _other_ ftrace_ops that also needs FTRACE_FL_TRAMP. Link: https://lkml.kernel.org/r/56c113aa9c3e10c19144a36d9684c7882bf09af5.1606412433.git.naveen.n.rao@linux.vnet.ibm.com Cc: stable@vger.kernel.org Fixes: a124692 ("ftrace: Enable trampoline when rec count returns back to one") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6988a61 upstream. A customer has reported that several files in their multi-threaded app were left with size of 0 because most of the read(2) calls returned -EINTR and they assumed no bytes were read. Obviously, they could have fixed it by simply retrying on -EINTR. We noticed that most of the -EINTR on read(2) were due to real-time signals sent by glibc to process wide credential changes (SIGRT_1), and its signal handler had been established with SA_RESTART, in which case those calls could have been automatically restarted by the kernel. Let the kernel decide to whether or not restart the syscalls when there is a signal pending in __smb_send_rqst() by returning -ERESTARTSYS. If it can't, it will return -EINTR anyway. Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2122533 upstream. This patch fixes a potential use-after-free bug in cifs_echo_request(). For instance, thread 1 -------- cifs_demultiplex_thread() clean_demultiplex_info() kfree(server) thread 2 (workqueue) -------- apic_timer_interrupt() smp_apic_timer_interrupt() irq_exit() __do_softirq() run_timer_softirq() call_timer_fn() cifs_echo_request() <- use-after-free in server ptr Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz> CC: Stable <stable@vger.kernel.org> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61e6fe5 upstream. If arbitration is lost, the master automatically changes to slave mode. I2SR_IBB may or may not be reset by hardware. Raising a STOP condition by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB. So calling i2c_imx_bus_busy() is not required and would busy-wait until timeout. Signed-off-by: Christian Eggers <ceggers@arri.de> Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove # the 3rd argument from the calls to # i2c_imx_bus_busy(). Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 600c084 upstream. Paulian reported a crash that happens when a dock is unplugged during hibernation: [78436.228217] thunderbolt 0-1: device disconnected [78436.228365] BUG: kernel NULL pointer dereference, address: 00000000000001e0 ... [78436.228397] RIP: 0010:icm_free_unplugged_children+0x109/0x1a0 ... [78436.228432] Call Trace: [78436.228439] icm_rescan_work+0x24/0x30 [78436.228444] process_one_work+0x1a3/0x3a0 [78436.228449] worker_thread+0x30/0x370 [78436.228454] ? process_one_work+0x3a0/0x3a0 [78436.228457] kthread+0x13d/0x160 [78436.228461] ? kthread_park+0x90/0x90 [78436.228465] ret_from_fork+0x1f/0x30 This happens because remove_unplugged_switch() calls tb_switch_remove() that releases the memory pointed by sw so the following lines reference to a memory that might be released already. Fix this by saving pointer to the parent device before calling tb_switch_remove(). Reported-by: Paulian Bogdan Marinca <paulian@marinca.net> Fixes: 4f7c2e0 ("thunderbolt: Make sure device runtime resume completes before taking domain lock") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 777a771 upstream. Ville noticed that the last mocs entry is used unconditionally by the HW when it performs cache evictions, and noted that while the value is not meant to be writable by the driver, we should program it to a reasonable value nevertheless. As it turns out, we can change the value of mocs:63 and the value we were programming into it would cause hard hangs in conjunction with atomic operations. v2: Add details from bspec about how it is used by HW Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2707 Fixes: 3bbaba0 ("drm/i915: Added Programming of the MOCS") Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Jason Ekstrand <jason@jlekstrand.net> Cc: <stable@vger.kernel.org> # v4.3+ Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20201126140841.1982-1-chris@chris-wilson.co.uk (cherry picked from commit 977933b) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42f6870 upstream. Commit c1a6c5a ("scsi: mpt3sas: For NVME device, issue a protocol level reset") modified the ioctl path 'timeout' variable type to u8 from unsigned long, limiting the maximum timeout value that the driver can support to 255 seconds. If the management application is requesting a higher value the resulting timeout will be zero. The operation times out immediately and the ioctl request fails. Change datatype back to unsigned long. Link: https://lore.kernel.org/r/20201125094838.4340-1-suganath-prabu.subramani@broadcom.com Fixes: c1a6c5a ("scsi: mpt3sas: For NVME device, issue a protocol level reset") Cc: <stable@vger.kernel.org> #v4.18+ Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67aa3ec upstream. Advance the maximum number of arguments to 16. This fixes issue where certain operations, combined with table configured args, exceed 10 arguments. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Fixes: 48debaf ("dm: add writecache target") Cc: stable@vger.kernel.org # v4.18+ Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
… MCE commit a1ee281 upstream. This can be hit by an HPT guest running on an HPT host and bring down the host, so it's quite important to fix. Fixes: 7290f3b ("powerpc/64s/powernv: machine check dump SLB contents") Cc: stable@vger.kernel.org # v5.4+ Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Mahesh Salgaonkar <mahesh@linux.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20201128070728.825934-2-npiggin@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb4c691 upstream. There is currently no way to convey the affinity of an interrupt via irq_create_mapping(), which creates issues for devices that expect that affinity to be managed by the kernel. In order to sort this out, rename irq_create_mapping() to irq_create_mapping_affinity() with an additional affinity parameter that can be passed down to irq_domain_alloc_descs(). irq_create_mapping() is re-implemented as a wrapper around irq_create_mapping_affinity(). No functional change. Fixes: e75eafb ("genirq/msi: Switch to new irq spreading infrastructure") Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Greg Kurz <groug@kaod.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201126082852.1178497-2-lvivier@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ea69a5 upstream. With virtio multiqueue, normally each queue IRQ is mapped to a CPU. Commit 0d9f0a5 ("virtio_scsi: use virtio IRQ affinity") exposed an existing shortcoming of the arch code by moving virtio_scsi to the automatic IRQ affinity assignment. The affinity is correctly computed in msi_desc but this is not applied to the system IRQs. It appears the affinity is correctly passed to rtas_setup_msi_irqs() but lost at this point and never passed to irq_domain_alloc_descs() (see commit 06ee6d5 ("genirq: Add affinity hint to irq allocation")) because irq_create_mapping() doesn't take an affinity parameter. Use the new irq_create_mapping_affinity() function, which allows to forward the affinity setting from rtas_setup_msi_irqs() to irq_domain_alloc_descs(). With this change, the virtqueues are correctly dispatched between the CPUs on pseries. Fixes: e75eafb ("genirq/msi: Switch to new irq spreading infrastructure") Signed-off-by: Laurent Vivier <lvivier@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Greg Kurz <groug@kaod.org> Acked-by: Michael Ellerman <mpe@ellerman.id.au> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20201126082852.1178497-3-lvivier@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8947833 upstream. The dm_get_live_table() function makes RCU read lock so dm_put_live_table() must be called even if dm_table map is not found. Fixes: e76239a ("block: add a report_zones method") Cc: stable@vger.kernel.org Signed-off-by: Sergei Shtepa <sergei.shtepa@veeam.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bde3808 upstream. Fixes sparse warnings: drivers/md/dm.c:508:12: warning: context imbalance in 'dm_prepare_ioctl' - wrong count at exit drivers/md/dm.c:543:13: warning: context imbalance in 'dm_unprepare_ioctl' - wrong count at exit Fixes: 971888c ("dm: hold DM table for duration of ioctl rather than use blkdev_get") Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e9a5ae upstream. Since insn.prefixes.nbytes can be bigger than the size of insn.prefixes.bytes[] when a prefix is repeated, the proper check must be insn.prefixes.bytes[i] != 0 and i < 4 instead of using insn.prefixes.nbytes. Introduce a for_each_insn_prefix() macro for this purpose. Debugged by Kees Cook <keescook@chromium.org>. [ bp: Massage commit message, sync with the respective header in tools/ and drop "we". ] Fixes: 2b14449 ("uprobes, mm, x86: Add the ability to install and remove uprobes breakpoints") Reported-by: syzbot+9b64b619f10f19d19a7c@syzkaller.appspotmail.com Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/160697103739.3146288.7437620795200799020.stgit@devnote2 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2bf509d upstream. 'format_corename()' will splite 'core_pattern' on spaces when it is in pipe mode, and take helper_argv[0] as the path to usermode executable. It works fine in most cases. However, if there is a space between '|' and '/file/path', such as '| /usr/lib/systemd/systemd-coredump %P %u %g', then helper_argv[0] will be parsed as '', and users will get a 'Core dump to | disabled'. It is not friendly to users, as the pattern above was valid previously. Fix this by ignoring the spaces between '|' and '/file/path'. Fixes: 315c692 ("coredump: split pipe command whitespace before expanding template") Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Cc: Paul Wise <pabs3@bonedaddy.net> Cc: Jakub Wilk <jwilk@jwilk.net> [https://bugs.debian.org/924398] Cc: Neil Horman <nhorman@tuxdriver.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/5fb62870.1c69fb81.8ef5d.af76@mx.google.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8199be0 upstream. When investigating a slab cache bloat problem, significant amount of negative dentry cache was seen, but confusingly they neither got shrunk by reclaimer (the host has very tight memory) nor be shrunk by dropping cache. The vmcore shows there are over 14M negative dentry objects on lru, but tracing result shows they were even not scanned at all. Further investigation shows the memcg's vfs shrinker_map bit is not set. So the reclaimer or dropping cache just skip calling vfs shrinker. So we have to reboot the hosts to get the memory back. I didn't manage to come up with a reproducer in test environment, and the problem can't be reproduced after rebooting. But it seems there is race between shrinker map bit clear and reparenting by code inspection. The hypothesis is elaborated as below. The memcg hierarchy on our production environment looks like: root / \ system user The main workloads are running under user slice's children, and it creates and removes memcg frequently. So reparenting happens very often under user slice, but no task is under user slice directly. So with the frequent reparenting and tight memory pressure, the below hypothetical race condition may happen: CPU A CPU B reparent dst->nr_items == 0 shrinker: total_objects == 0 add src->nr_items to dst set_bit return SHRINK_EMPTY clear_bit child memcg offline replace child's kmemcg_id with parent's (in memcg_offline_kmem()) list_lru_del() between shrinker runs see parent's kmemcg_id dec dst->nr_items reparent again dst->nr_items may go negative due to concurrent list_lru_del() The second run of shrinker: read nr_items without any synchronization, so it may see intermediate negative nr_items then total_objects may return 0 coincidently keep the bit cleared dst->nr_items != 0 skip set_bit add scr->nr_item to dst After this point dst->nr_item may never go zero, so reparenting will not set shrinker_map bit anymore. And since there is no task under user slice directly, so no new object will be added to its lru to set the shrinker map bit either. That bit is kept cleared forever. How does list_lru_del() race with reparenting? It is because reparenting replaces children's kmemcg_id to parent's without protecting from nlru->lock, so list_lru_del() may see parent's kmemcg_id but actually deleting items from child's lru, but dec'ing parent's nr_items, so the parent's nr_items may go negative as commit 2788cf0 ("memcg: reparent list_lrus and free kmemcg_id on css offline") says. Since it is impossible that dst->nr_items goes negative and src->nr_items goes zero at the same time, so it seems we could set the shrinker map bit iff src->nr_items != 0. We could synchronize list_lru_count_one() and reparenting with nlru->lock, but it seems checking src->nr_items in reparenting is the simplest and avoids lock contention. Fixes: fae91d6 ("mm/list_lru.c: set bit in memcg shrinker bitmap on first list_lru item appearance") Suggested-by: Roman Gushchin <guro@fb.com> Signed-off-by: Yang Shi <shy828301@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Roman Gushchin <guro@fb.com> Reviewed-by: Shakeel Butt <shakeelb@google.com> Acked-by: Kirill Tkhai <ktkhai@virtuozzo.com> Cc: Vladimir Davydov <vdavydov.dev@gmail.com> Cc: <stable@vger.kernel.org> [4.19] Link: https://lkml.kernel.org/r/20201202171749.264354-1-shy828301@gmail.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b11a76b upstream. We can't call kvfree() with a spin lock held, so defer it. Fixes a might_sleep() runtime warning. Fixes: 873d7bc ("mm/swapfile.c: use kvzalloc for swap_info_struct allocation") Signed-off-by: Qian Cai <qcai@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Hugh Dickins <hughd@google.com> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20201202151549.10350-1-qcai@redhat.com Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f099209 upstream. Speakup exposing a line discipline allows userland to try to use it, while it is deemed to be useless, and thus uselessly exposes potential bugs. One of them is simply that in such a case if the line sends data, spk_ttyio_receive_buf2 is called and crashes since spk_ttyio_synth is NULL. This change restricts the use of the speakup line discipline to speakup drivers, thus avoiding such kind of issues altogether. Cc: stable@vger.kernel.org Reported-by: Shisong Qin <qinshisong1205@gmail.com> Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Tested-by: Shisong Qin <qinshisong1205@gmail.com> Link: https://lore.kernel.org/r/20201129193523.hm3f6n5xrn6fiyyc@function Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 384a956 upstream. According to the "VFxxx Controller Reference Manual" (and the comment block starting at line 97), Vybrid requires writing a one for clearing an interrupt flag. Syncing the method for clearing I2SR_IIF in i2c_imx_isr(). Signed-off-by: Christian Eggers <ceggers@arri.de> Fixes: 4b77502 ("i2c: imx: add struct to hold more configurable quirks") Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1de67a3 upstream. Arbitration Lost (IAL) can happen after every single byte transfer. If arbitration is lost, the I2C hardware will autonomously switch from master mode to slave. If a transfer is not aborted in this state, consecutive transfers will not be executed by the hardware and will timeout. Signed-off-by: Christian Eggers <ceggers@arri.de> Tested (not extensively) on Vybrid VF500 (Toradex VF50): Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 666224b ] The DMA channel was not released if either devm_request_irq() or devm_spi_register_controller() failed. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Link: https://lore.kernel.org/r/20191212135550.4634-3-peter.ujfalusi@ti.com Signed-off-by: Mark Brown <broonie@kernel.org> [lukas: backport to 5.4-stable] Signed-off-by: Lukas Wunner <lukas@wunner.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4165bf0 upstream. According to the AMD IOMMU spec, the commit 73db2fc ("iommu/amd: Increase interrupt remapping table limit to 512 entries") also requires the interrupt table length (IntTabLen) to be set to 9 (power of 2) in the device table mapping entry (DTE). Fixes: 73db2fc ("iommu/amd: Increase interrupt remapping table limit to 512 entries") Reported-by: Jerry Snitselaar <jsnitsel@redhat.com> Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Link: https://lore.kernel.org/r/20201207091920.3052-1-suravee.suthikulpanit@amd.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bcee527 upstream. When the instances were able to use their own options, the userstacktrace option was left hardcoded for the top level. This made the instance userstacktrace option bascially into a nop, and will confuse users that set it, but nothing happens (I was confused when it happened to me!) Cc: stable@vger.kernel.org Fixes: 1627014 ("tracing: Add trace options for core options to instances") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4f134b8 upstream. Lilith >_> and Claudio Bozzato of Cisco Talos security team reported that collect_syscall() improperly casts the syscall registers to 64-bit values leaking the uninitialized last 24 bytes on 32-bit platforms, that are visible in /proc/self/syscall. The cause is that info->data.args are u64 while syscall_get_arguments() uses longs, as hinted by the bogus pointer cast in the function. Let's just proceed like the other call places, by retrieving the registers into an array of longs before assigning them to the caller's array. This was successfully tested on x86_64, i386 and ppc32. Reference: CVE-2020-28588, TALOS-2020-1211 Fixes: 631b7ab ("ptrace: Remove maxargs from task_current_syscall()") Cc: Greg KH <greg@kroah.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Michael Ellerman <mpe@ellerman.id.au> (ppc32) Signed-off-by: Willy Tarreau <w@1wt.eu> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…peration sanity check commit d73ff9b upstream. To detect potential bugs in CAN protocol implementations (double removal of receiver entries) a WARN() statement has been used if no matching list item was found for removal. The fault injection issued by syzkaller was able to create a situation where the closing of a socket runs simultaneously to the notifier call chain for removing the CAN network device in use. This case is very unlikely in real life but it doesn't break anything. Therefore we just replace the WARN() statement with pr_warn() to preserve the notification for the CAN protocol development. Reported-by: syzbot+381d06e0c8eaacb8706f@syzkaller.appspotmail.com Reported-by: syzbot+d0ddd88c9a7432f041e6@syzkaller.appspotmail.com Reported-by: syzbot+76d62d3b8162883c7d11@syzkaller.appspotmail.com Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Link: https://lore.kernel.org/r/20201126192140.14350-1-socketcan@hartkopp.net Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7787215 upstream. If gfs2 tries to mount a (corrupt) file system that has no resource groups it still tries to set preferences on the first one, which causes a kernel null pointer dereference. This patch adds a check to function gfs2_ri_update so this condition is detected and reported back as an error. Reported-by: syzbot+e3f23ce40269a4c9053a@syzkaller.appspotmail.com Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 68ad89d upstream. syzbot found that we are not validating user input properly before copying 16 bytes [1]. Using NLA_BINARY in ipaddr_policy[] for IPv6 address is not correct, since it ensures at most 16 bytes were provided. We should instead make sure user provided exactly 16 bytes. In old kernels (before v4.20), fix would be to remove the NLA_BINARY, since NLA_POLICY_EXACT_LEN() was not yet available. [1] BUG: KMSAN: uninit-value in hash_ip6_add+0x1cba/0x3a50 net/netfilter/ipset/ip_set_hash_gen.h:892 CPU: 1 PID: 11611 Comm: syz-executor.0 Not tainted 5.10.0-rc4-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x21c/0x280 lib/dump_stack.c:118 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118 __msan_warning+0x5f/0xa0 mm/kmsan/kmsan_instr.c:197 hash_ip6_add+0x1cba/0x3a50 net/netfilter/ipset/ip_set_hash_gen.h:892 hash_ip6_uadt+0x976/0xbd0 net/netfilter/ipset/ip_set_hash_ip.c:267 call_ad+0x329/0xd00 net/netfilter/ipset/ip_set_core.c:1720 ip_set_ad+0x111f/0x1440 net/netfilter/ipset/ip_set_core.c:1808 ip_set_uadd+0xf6/0x110 net/netfilter/ipset/ip_set_core.c:1833 nfnetlink_rcv_msg+0xc7d/0xdf0 net/netfilter/nfnetlink.c:252 netlink_rcv_skb+0x70a/0x820 net/netlink/af_netlink.c:2494 nfnetlink_rcv+0x4f0/0x4380 net/netfilter/nfnetlink.c:600 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline] netlink_unicast+0x11da/0x14b0 net/netlink/af_netlink.c:1330 netlink_sendmsg+0x173c/0x1840 net/netlink/af_netlink.c:1919 sock_sendmsg_nosec net/socket.c:651 [inline] sock_sendmsg net/socket.c:671 [inline] ____sys_sendmsg+0xc7a/0x1240 net/socket.c:2353 ___sys_sendmsg net/socket.c:2407 [inline] __sys_sendmsg+0x6d5/0x830 net/socket.c:2440 __do_sys_sendmsg net/socket.c:2449 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x45deb9 Code: 0d b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 db b3 fb ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007fe2e503fc78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e RAX: ffffffffffffffda RBX: 0000000000029ec0 RCX: 000000000045deb9 RDX: 0000000000000000 RSI: 0000000020000140 RDI: 0000000000000003 RBP: 000000000118bf60 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 000000000118bf2c R13: 000000000169fb7f R14: 00007fe2e50409c0 R15: 000000000118bf2c Uninit was stored to memory at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:121 [inline] kmsan_internal_chain_origin+0xad/0x130 mm/kmsan/kmsan.c:289 __msan_chain_origin+0x57/0xa0 mm/kmsan/kmsan_instr.c:147 ip6_netmask include/linux/netfilter/ipset/pfxlen.h:49 [inline] hash_ip6_netmask net/netfilter/ipset/ip_set_hash_ip.c:185 [inline] hash_ip6_uadt+0xb1c/0xbd0 net/netfilter/ipset/ip_set_hash_ip.c:263 call_ad+0x329/0xd00 net/netfilter/ipset/ip_set_core.c:1720 ip_set_ad+0x111f/0x1440 net/netfilter/ipset/ip_set_core.c:1808 ip_set_uadd+0xf6/0x110 net/netfilter/ipset/ip_set_core.c:1833 nfnetlink_rcv_msg+0xc7d/0xdf0 net/netfilter/nfnetlink.c:252 netlink_rcv_skb+0x70a/0x820 net/netlink/af_netlink.c:2494 nfnetlink_rcv+0x4f0/0x4380 net/netfilter/nfnetlink.c:600 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline] netlink_unicast+0x11da/0x14b0 net/netlink/af_netlink.c:1330 netlink_sendmsg+0x173c/0x1840 net/netlink/af_netlink.c:1919 sock_sendmsg_nosec net/socket.c:651 [inline] sock_sendmsg net/socket.c:671 [inline] ____sys_sendmsg+0xc7a/0x1240 net/socket.c:2353 ___sys_sendmsg net/socket.c:2407 [inline] __sys_sendmsg+0x6d5/0x830 net/socket.c:2440 __do_sys_sendmsg net/socket.c:2449 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Uninit was stored to memory at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:121 [inline] kmsan_internal_chain_origin+0xad/0x130 mm/kmsan/kmsan.c:289 kmsan_memcpy_memmove_metadata+0x25e/0x2d0 mm/kmsan/kmsan.c:226 kmsan_memcpy_metadata+0xb/0x10 mm/kmsan/kmsan.c:246 __msan_memcpy+0x46/0x60 mm/kmsan/kmsan_instr.c:110 ip_set_get_ipaddr6+0x2cb/0x370 net/netfilter/ipset/ip_set_core.c:310 hash_ip6_uadt+0x439/0xbd0 net/netfilter/ipset/ip_set_hash_ip.c:255 call_ad+0x329/0xd00 net/netfilter/ipset/ip_set_core.c:1720 ip_set_ad+0x111f/0x1440 net/netfilter/ipset/ip_set_core.c:1808 ip_set_uadd+0xf6/0x110 net/netfilter/ipset/ip_set_core.c:1833 nfnetlink_rcv_msg+0xc7d/0xdf0 net/netfilter/nfnetlink.c:252 netlink_rcv_skb+0x70a/0x820 net/netlink/af_netlink.c:2494 nfnetlink_rcv+0x4f0/0x4380 net/netfilter/nfnetlink.c:600 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline] netlink_unicast+0x11da/0x14b0 net/netlink/af_netlink.c:1330 netlink_sendmsg+0x173c/0x1840 net/netlink/af_netlink.c:1919 sock_sendmsg_nosec net/socket.c:651 [inline] sock_sendmsg net/socket.c:671 [inline] ____sys_sendmsg+0xc7a/0x1240 net/socket.c:2353 ___sys_sendmsg net/socket.c:2407 [inline] __sys_sendmsg+0x6d5/0x830 net/socket.c:2440 __do_sys_sendmsg net/socket.c:2449 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:121 [inline] kmsan_internal_poison_shadow+0x5c/0xf0 mm/kmsan/kmsan.c:104 kmsan_slab_alloc+0x8d/0xe0 mm/kmsan/kmsan_hooks.c:76 slab_alloc_node mm/slub.c:2906 [inline] __kmalloc_node_track_caller+0xc61/0x15f0 mm/slub.c:4512 __kmalloc_reserve net/core/skbuff.c:142 [inline] __alloc_skb+0x309/0xae0 net/core/skbuff.c:210 alloc_skb include/linux/skbuff.h:1094 [inline] netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline] netlink_sendmsg+0xdb8/0x1840 net/netlink/af_netlink.c:1894 sock_sendmsg_nosec net/socket.c:651 [inline] sock_sendmsg net/socket.c:671 [inline] ____sys_sendmsg+0xc7a/0x1240 net/socket.c:2353 ___sys_sendmsg net/socket.c:2407 [inline] __sys_sendmsg+0x6d5/0x830 net/socket.c:2440 __do_sys_sendmsg net/socket.c:2449 [inline] __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: a7b4f98 ("netfilter: ipset: IP set core support") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Acked-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d966ddc upstream. In the commit fdeba99 ("tipc: fix use-after-free in tipc_bcast_get_mode"), we're trying to make sure the tipc_net_finalize_work work item finished if it enqueued. But calling flush_scheduled_work() is not just affecting above work item but either any scheduled work. This has turned out to be overkill and caused to deadlock as syzbot reported: ====================================================== WARNING: possible circular locking dependency detected 5.9.0-rc2-next-20200828-syzkaller #0 Not tainted ------------------------------------------------------ kworker/u4:6/349 is trying to acquire lock: ffff8880aa063d38 ((wq_completion)events){+.+.}-{0:0}, at: flush_workqueue+0xe1/0x13e0 kernel/workqueue.c:2777 but task is already holding lock: ffffffff8a879430 (pernet_ops_rwsem){++++}-{3:3}, at: cleanup_net+0x9b/0xb10 net/core/net_namespace.c:565 [...] Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(pernet_ops_rwsem); lock(&sb->s_type->i_mutex_key#13); lock(pernet_ops_rwsem); lock((wq_completion)events); *** DEADLOCK *** [...] v1: To fix the original issue, we replace above calling by introducing a bit flag. When a namespace cleaned-up, bit flag is set to zero and: - tipc_net_finalize functionial just does return immediately. - tipc_net_finalize_work does not enqueue into the scheduled work queue. v2: Use cancel_work_sync() helper to make sure ONLY the tipc_net_finalize_work() stopped before releasing bcbase object. Reported-by: syzbot+d5aa7e0385f6a5d0f4fd@syzkaller.appspotmail.com Fixes: fdeba99 ("tipc: fix use-after-free in tipc_bcast_get_mode") Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: Hoang Huu Le <hoang.h.le@dektech.com.au> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3fba05a upstream. Fix to return a negative error code from the error handling case instead of 0 in function wm_adsp_load(), as done elsewhere in this function. Fixes: 170b1e1 ("ASoC: wm_adsp: Add support for new Halo core DSPs") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Luo Meng <luomeng12@huawei.com> Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20201123133839.4073787-1-luomeng12@huawei.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74a8c81 upstream. This code does not ensure that the whole buffer is initialized and none of the callers check for errors so potentially none of the buffer is initialized. Add a memset to eliminate this bug. Fixes: e303748 ("rtw88: new Realtek 802.11ac driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/X8ilOfVz3pf0T5ec@mwanda Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e9acf02 upstream. Fix to return the error code from qup_i2c_change_state() instaed of 0 in qup_i2c_bam_schedule_desc(). Fixes: fbf9921 ("i2c: qup: Fix error handling") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 857c4c0 upstream. Building on arch/s390/ results in this build error: cc1: some warnings being treated as errors ../drivers/md/dm-writecache.c: In function 'persistent_memory_claim': ../drivers/md/dm-writecache.c:323:1: error: no return statement in function returning non-void [-Werror=return-type] Fix this by replacing the BUG() with an -EOPNOTSUPP return. Fixes: 48debaf ("dm: add writecache target") Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 855b698 upstream. Fix to return a negative error code from the error handling case instead of 0 in function i8042_setup_aux(), as done elsewhere in this function. Fixes: f811341 ("Input: i8042 - use platform_driver_probe") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Luo Meng <luomeng12@huawei.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20201123133420.4071187-1-luomeng12@huawei.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0700df upstream. There are reports wrt lockdep splat in nftables, e.g.: ------------[ cut here ]------------ WARNING: CPU: 2 PID: 31416 at net/netfilter/nf_tables_api.c:622 lockdep_nfnl_nft_mutex_not_held+0x28/0x38 [nf_tables] ... These are caused by an earlier, unrelated bug such as a n ABBA deadlock in a different subsystem. In such an event, lockdep is disabled and lockdep_is_held returns true unconditionally. This then causes the WARN() in nf_tables. Make the WARN conditional on lockdep still active to avoid this. Fixes: f102d66 ("netfilter: nf_tables: use dedicated mutex to guard transactions") Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org> Link: https://lore.kernel.org/linux-kselftest/CA+G9fYvFUpODs+NkSYcnwKnXm62tmP=ksLeBPmB+KFrB2rvCtQ@mail.gmail.com/ Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c78e9e upstream. This patch adds nft_flow_rule_set_addr_type() to set the address type from the nft_payload expression accordingly. If the address type is not set in the control dissector then a rule that matches either on source or destination IP address does not work. After this patch, nft hardware offload generates the flow dissector configuration as tc-flower does to match on an IP address. This patch has been also tested functionally to make sure packets are filtered out by the NIC. This is also getting the code aligned with the existing netfilter flow offload infrastructure which is also setting the control dissector. Fixes: c9626a2 ("netfilter: nf_tables: add hardware offload support") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
…ixes bytes commit 12cb908 upstream Since insn.prefixes.nbytes can be bigger than the size of insn.prefixes.bytes[] when a prefix is repeated, the proper check must be insn.prefixes.bytes[i] != 0 and i < 4 instead of using insn.prefixes.nbytes. Use the new for_each_insn_prefix() macro which does it correctly. Debugged by Kees Cook <keescook@chromium.org>. [ bp: Massage commit message. ] Fixes: 32d0b95 ("x86/insn-eval: Add utility functions to get segment selector") Reported-by: syzbot+9b64b619f10f19d19a7c@syzkaller.appspotmail.com Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/160697104969.3146288.16329307586428270032.stgit@devnote2 [sudip: adjust context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c02bd11 upstream. This reverts commit 4179b00 ("geneve: pull IP header before ECN decapsulation"). Eric says: "network header should have been pulled already before hitting geneve_rx()". Let's revert the syzbot fix since it's causing more harm than good, and revisit. Suggested-by: Eric Dumazet <edumazet@google.com> Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 4179b00 ("geneve: pull IP header before ECN decapsulation") Link: https://bugzilla.kernel.org/show_bug.cgi?id=210569 Link: https://lore.kernel.org/netdev/CANn89iJVWfb=2i7oU1=D55rOyQnBbbikf+Mc6XHMkY7YX-yGEw@mail.gmail.com/ Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com> Tested-by: Shuah Khan <skhan@linuxfoundation.org> Tested-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Linux Kernel Functional Testing <lkft@linaro.org> Link: https://lore.kernel.org/r/20201210164728.074574869@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the 5.4.83 stable release Conflicts: - drivers/i2c/busses/i2c-imx.c: Merge commits [0af1413] from NXP tree with commit [a5dafefa7ac01a47f954f9dd77df1457f50ff1a1] from upstream, replace the function i2c_imx_clr_if_bit in NXP tree to i2c_imx_clear_irq from upstream. Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
otavio
pushed a commit
that referenced
this pull request
Aug 8, 2025
commit 5db0d25 upstream. w/ below testcase, resize will generate a corrupted image which contains inconsistent metadata, so when mounting such image, it will trigger kernel panic: touch img truncate -s $((512*1024*1024*1024)) img mkfs.f2fs -f img $((256*1024*1024)) resize.f2fs -s -i img -t $((1024*1024*1024)) mount img /mnt/f2fs ------------[ cut here ]------------ kernel BUG at fs/f2fs/segment.h:863! Oops: invalid opcode: 0000 [#1] SMP PTI CPU: 11 UID: 0 PID: 3922 Comm: mount Not tainted 6.15.0-rc1+ #191 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:f2fs_ra_meta_pages+0x47c/0x490 Call Trace: f2fs_build_segment_manager+0x11c3/0x2600 f2fs_fill_super+0xe97/0x2840 mount_bdev+0xf4/0x140 legacy_get_tree+0x2b/0x50 vfs_get_tree+0x29/0xd0 path_mount+0x487/0xaf0 __x64_sys_mount+0x116/0x150 do_syscall_64+0x82/0x190 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fdbfde1bcfe The reaseon is: sit_i->bitmap_size is 192, so size of sit bitmap is 192*8=1536, at maximum there are 1536 sit blocks, however MAIN_SEGS is 261893, so that sit_blk_cnt is 4762, build_sit_entries() -> current_sit_addr() tries to access out-of-boundary in sit_bitmap at offset from [1536, 4762), once sit_bitmap and sit_bitmap_mirror is not the same, it will trigger f2fs_bug_on(). Let's add sanity check in f2fs_sanity_check_ckpt() to avoid panic. Cc: stable@vger.kernel.org Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ivitro
pushed a commit
to ivitro/linux-fslc
that referenced
this pull request
Sep 2, 2025
commit 5db0d25 upstream. w/ below testcase, resize will generate a corrupted image which contains inconsistent metadata, so when mounting such image, it will trigger kernel panic: touch img truncate -s $((512*1024*1024*1024)) img mkfs.f2fs -f img $((256*1024*1024)) resize.f2fs -s -i img -t $((1024*1024*1024)) mount img /mnt/f2fs ------------[ cut here ]------------ kernel BUG at fs/f2fs/segment.h:863! Oops: invalid opcode: 0000 [Freescale#1] SMP PTI CPU: 11 UID: 0 PID: 3922 Comm: mount Not tainted 6.15.0-rc1+ Freescale#191 PREEMPT(voluntary) Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.16.3-debian-1.16.3-2 04/01/2014 RIP: 0010:f2fs_ra_meta_pages+0x47c/0x490 Call Trace: f2fs_build_segment_manager+0x11c3/0x2600 f2fs_fill_super+0xe97/0x2840 mount_bdev+0xf4/0x140 legacy_get_tree+0x2b/0x50 vfs_get_tree+0x29/0xd0 path_mount+0x487/0xaf0 __x64_sys_mount+0x116/0x150 do_syscall_64+0x82/0x190 entry_SYSCALL_64_after_hwframe+0x76/0x7e RIP: 0033:0x7fdbfde1bcfe The reaseon is: sit_i->bitmap_size is 192, so size of sit bitmap is 192*8=1536, at maximum there are 1536 sit blocks, however MAIN_SEGS is 261893, so that sit_blk_cnt is 4762, build_sit_entries() -> current_sit_addr() tries to access out-of-boundary in sit_bitmap at offset from [1536, 4762), once sit_bitmap and sit_bitmap_mirror is not the same, it will trigger f2fs_bug_on(). Let's add sanity check in f2fs_sanity_check_ckpt() to avoid panic. Cc: stable@vger.kernel.org Signed-off-by: Chao Yu <chao@kernel.org> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
otavio
pushed a commit
that referenced
this pull request
Dec 17, 2025
[ Upstream commit fbe6070 ] In legacy mode, SSPTPTR is ignored if TT is not 00b or 01b. SSPTPTR maybe uninitialized or zero in that case and may cause oops like: Oops: general protection fault, probably for non-canonical address 0xf00087d3f000f000: 0000 [#1] SMP NOPTI CPU: 2 UID: 0 PID: 786 Comm: cat Not tainted 6.16.0 #191 PREEMPT(voluntary) Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.17.0-5.fc42 04/01/2014 RIP: 0010:pgtable_walk_level+0x98/0x150 RSP: 0018:ffffc90000f279c0 EFLAGS: 00010206 RAX: 0000000040000000 RBX: ffffc90000f27ab0 RCX: 000000000000001e RDX: 0000000000000003 RSI: f00087d3f000f000 RDI: f00087d3f0010000 RBP: ffffc90000f27a00 R08: ffffc90000f27a98 R09: 0000000000000002 R10: 0000000000000000 R11: 0000000000000000 R12: f00087d3f000f000 R13: 0000000000000000 R14: 0000000040000000 R15: ffffc90000f27a98 FS: 0000764566dcb740(0000) GS:ffff8881f812c000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000764566d44000 CR3: 0000000109d81003 CR4: 0000000000772ef0 PKRU: 55555554 Call Trace: <TASK> pgtable_walk_level+0x88/0x150 domain_translation_struct_show.isra.0+0x2d9/0x300 dev_domain_translation_struct_show+0x20/0x40 seq_read_iter+0x12d/0x490 ... Avoid walking the page table if TT is not 00b or 01b. Fixes: 2b437e8 ("iommu/vt-d: debugfs: Support dumping a specified page table") Signed-off-by: Vineeth Pillai (Google) <vineeth@bitbyteword.org> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20250814163153.634680-1-vineeth@bitbyteword.org Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <joerg.roedel@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
20 participants
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
Notes to upgrade, following merge conflicts were resolved:
v5.4.83:
drivers/i2c/busses/i2c-imx.c:Merge commits 0af1413 ("i2c: imx: correct code of errata A-010650 for layerscape platform") from NXP tree with commit 83366a7 ("i2c: imx: Fix reset of I2SR_IAL flag") from upstream, replace the function i2c_imx_clr_if_bit in NXP tree to i2c_imx_clear_irq from upstream.
Kernel has been built for both aarch64 (
imx_v8_defconfig) and arm32 (imx_v7_defconfig).-- andrey